Puslefire Haste 3 Wireless

Puslefire Haste 3 Wireless

Articles - Category Page

(10)
H
HyperX Pulsefire 3 Wireless in Wired Mode

Connect the mouse to a PC or game console using the included USB cable. USB connectivity will override the selected power mode.

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
Pulsefire Haste 3 Wireless Battery Replacement

Warning: Improper or forced battery installation may cause permanent damage and is not covered under warranty. ​ Switch power mode to "OFF". Remove the mouse skates with a flat plastic tool to reveal and unscrew the 4x Torx 2 Security screws below. Gently separate and lift the top shell from the bot

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless Polling Rate

The default polling rate is 1K Power OFF the mouse completely. Press and hold the DPI button. While holding the DPI button, switch the mouse to 2.4G mode. Repeat cycle to the next polling rate; the wheel LED fast blinks twice. There are 3 default presets: 1000Hz (White) 4000Hz (Cyan) 8000Hz (Magenta

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless DPI Presets

There are 4 default DPI presets: 400 DPI (Red) 800 DPI (Blue) 1600 DPI (Yellow) 3200 DPI (Green) *Max DPI up to 42000 DPI

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
How to Replace the Skates on the Pulsefire Haste 3 Wireless

Turn the mouse upside down.Gently slide a plastic pry tool under the edge of a skate.Slowly lift and peel the skate away from the mouse.Repeat for all skates.Remove all leftover adhesive residue and debris. (you may need to use rubbing alcohol and a microfiber cloth to get it completely clean).Allow

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless Bluetooth Pairing

Hold the left click button, right click button, and DPI buttons simultaneously until the mouse LED flashed blue.

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless Bluetooth Mode

Switch the mouse to Bluetooth power mode. Mouse will flash blue on first setup. Go to your computer's Bluetooth settings, search and connect to "Haste 3 WL".

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless Overview

A. Left Click Button B. Right Click Button C. Mouse Wheel D. Forward Button E. Back Button F. USB-C Port G. PTFE Skates H. HyperX Performance Sensor I. Power Mode Switch J. DPI Button K. Extra Mouse Skates L. 8K Wireless Desktop Dongle M. USB Charge/Data Cable

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless 2.4G Wireless Mode

Switch the mouse to 2.4G power mode Connect the wireless desktop dongle to a PC or game console using the included USB cable. For optimal placement, keep the wireless desktop dongle within 20cm of the mouse.

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless

H
HyperX Pulsefire Haste 3 Wireless Charging

Connect the mouse to a PC or game console using the included USB cable. *USB connectivity will override the selected power mode

Knowledge Base Article

 • 

Puslefire Haste 3 Wireless